51401052-100
Smart Peripheral Controller Card · Smart Peripheral Controller for History Module disk-drive communication and control
Lifecycle note: Use the unit nameplate, linked product PDF and current Honeywell documentation as the final references before approving a replacement.
Product Condition
Original New with One Year WarrantyParts Available
In Stock and Same Day ShippingDelivery Mode
Shipping via DHL Fedex or UPS etcEmail:
sales17@amikon.cnWhatsapp/Mob:
+86 15359408275Smart Peripheral Controller Card · TDC 3000 History Module
Honeywell 51401052-100 is the Smart Peripheral Controller circuit board used in TDC 3000 History Module storage configurations. Honeywell documentation assigns 51401052-100 the task of communicating with and controlling the Winchester disk drives and the associated SPC I/O board.
Honeywell 51401052-100 connects into the History Module disk subsystem through the SCSI bus. The SPC I/O board and Winchester Drive Interface hardware provide the path between 51401052-100 and one or two installed disk drives, so the surrounding drive, ribbon-cable and termination arrangement must remain consistent.
Honeywell 51401052-100 carries address pinning at TS1 for the installed SCSI configuration, while the TS2 revision setting is factory established and must not be altered in the field. The service manual also specifies revision G or later firmware for documented replacement configurations.
Honeywell 51401052-100 should be matched by complete assembly number, firmware level, TS1 pinning, slot position, SPC I/O pairing and History Module drive layout. We can provide 100% ORIGINAL NEW Honeywell 51401052-100 with factory seal, and we will provide 1 year warranty for you.
| Manufacturer | Honeywell |
|---|---|
| Model | 51401052-100 |
| Product type | Smart Peripheral Controller circuit board |
| System family | TDC 3000 History Module |
| Primary function | Communication with and control of Winchester disk drives and the SPC I/O board |
| Bus interface | SCSI through SPC I/O and drive-interface hardware |
| Address configuration | TS1 pinning; documented application uses SCSI address 7 |
| Revision setting | TS2 is factory set and must not be changed in the field |
| Documented firmware | Revision G or later for the referenced History Module configuration |
| Installation reference | Module chassis slot 3 in documented replacement procedure |
| Replacement checks | Firmware, TS1 pinning, drive arrangement, cables, terminators and SPC I/O pairing |
Use the installed-unit nameplate, linked product PDF and current Honeywell documentation as the final references before approving a replacement.
Honeywell 51401052-100 is a Smart Peripheral Controller circuit board for TDC 3000 History Module storage configurations.
Honeywell 51401052-100 communicates with and controls the Winchester disk drives and the associated SPC I/O board.
Honeywell 51401052-100 uses the SCSI path formed by the SPC I/O board, drive-interface hardware, ribbon cables and installed disk drives.
Honeywell 51401052-100 uses TS1 for SCSI address pinning; the documented History Module application uses SCSI address 7, while TS2 is factory set.
Honeywell 51401052-100 is documented with revision G or later firmware for the referenced replacement configurations.
Check the complete 51401052-100 assembly number, firmware, TS1 pinning, slot, SPC I/O board, disk layout, SCSI cabling and termination.
Yes. The complete Honeywell 51401052-100 identification and installed History Module configuration must be matched before ordering.
Technical information for Honeywell 51401052-100 can be checked in the linked Honeywell History Module service manual and against the installed unit.
We can supply Honeywell 51401052-100 in 100% original-new condition with factory seal and provide a 1-year warranty, subject to stock confirmation.
Send the model, complete identification, quantity, destination and nameplate photo. We will verify identification details before confirming availability and lead time.
Technical information is based on the linked product PDF and current Honeywell documentation. Final suitability must be verified against the exact installed unit and current official Honeywell documentation.
Visit us
32D Guomao Building, No.388, Hubin South Road, Siming District
Please read on, stay posted, subscribe, and we welcome you to tell us what you think.
Disclaimer : Salesplcauto sells new and surplus products and develops channels for purchasing such products. This website has not been approved or recognized by any of the listed manufacturers or trademarks. Salesplcauto is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.
Copyright @2026 SalesPlc Limited. Sitemap
/ Blog
/ XML
/ Terms And Conditions
/ Privacy Policy
Network Supported
About Us
Reliable Industrial Automation Parts, Global Supply Support SALES PLC works with a broad network of qualified suppliers to provide industrial automation components that meet our customers’ requirements for quality, availability, price, and delivery time. Our product portfolio covers PLC, DCS, HMI, control systems, safety systems, drives, communication modules, and other critical spare parts from leading brands, including Siemens, Emerson, Invensys Triconex, HIMA, GE, ABB, Honeywell, and Bently Nevada. More Than Products — Complete Supply Solutions Our strength goes beyond product sourcing. We work closely with end users, system integrators, maintenance teams, and industrial partners to identify suitable replacement parts and practical procurement solutions. Through integrated purchasing and online support, customers can send inquiries and place orders throughout the year. Our experienced team responds quickly and helps reduce downtime caused by unavailable or obsolete equipment. Our Team Our experienced team brings together product specialists, sourcing professionals, sales consultants, and customer service staff. We work together to provide clear communication and dependable support at every stage of the order. Growing Together for More Than 20 Years For more than 20 years, SALES PLC has continued to grow with the support and trust of customers, suppliers, and business partners around the world. Every project, inquiry, and partnership has helped us improve our service. Looking ahead, we remain committed to providing dependable products, responsive communication, and professional industrial automation solutions. Thank you to every customer and partner who has supported our journey. We look forward to building a stronger and more successful future together. Sustainable Partnerships SALES PLC believes in building long-term, mutually beneficial relationships with customers and suppliers. We focus on honest communication, responsible sourcing, continuous improvement, and reliable service. As industrial technology continues to evolve, we keep expanding our product knowledge and supplier network to support new systems, legacy equipment, and replacement-part requirements. Contact SALES PLC Our team is available during working hours to answer your questions, check product availability, and prepare a quotation.
Where to Find Us
32D Guomao Building, No.388, Hubin South Road, Siming District
+86 18150117685
sales1@amikon.cn
Follow Us
