Home Siemens

C79458-L2343-A2 Siemens Siemens Industrial Communication Communication Component

C79458-L2343-A2 Siemens Siemens Industrial Communication Communication Component

Siemens · Siemens Industrial Communication

C79458-L2343-A2
C79458-L2343-A2 is a Siemens Communication Component in the Siemens Industrial Communication family. Complete assembly code and revision to be matched.

Type
Communication Component
Family
Siemens Industrial Communication
Platform
Siemens Siemens Industrial Communication
Scope
Component
Application & Order CheckMatch C79458-L2343-A2 to the installed Siemens configuration
Application Fit
  • Maintenance of the identified Siemens communication installation
  • Documented Siemens Industrial Communication installation
  • Maintenance and migration with an approved project backup
Verify Before Order
  • Match label photos, host assembly, connector layout and supported driver/project.
  • Complete order code, suffix and hardware revision
  • Preserve the original configuration and validate communication with the approved host system.

Scope note: C79458-L2343-A2 is supplied as Communication Component; system engineering, accessories and site acceptance are verified separately.

  • Product Condition

    Original New with One Year Warranty
  • Parts Available

    In Stock and Same Day Shipping
  • Delivery Mode

    Shipping via DHL Fedex or UPS etc
  • Email:

    sales1@amikon.cn
  • Whatsapp/Mob:

    +86 18150117685
Description
Technical Product Profile

Siemens C79458-L2343-A2

Siemens Industrial Communication Communication Component

Siemens Industrial CommunicationSiemensVerify suffixComponent

Overview

C79458-L2343-A2 is a Siemens Communication Component in the Siemens Industrial Communication family. Complete assembly code and revision to be matched. Applications include maintenance of the identified siemens communication installation.

Suitability depends on the host Siemens platform, electrical or communication interfaces, firmware, accessories and approved engineering configuration. Verify the complete assembly rather than treating C79458-L2343-A2 as a standalone system.

Ordering note: confirm the exact catalog code, revision, hardware fit, application conditions and current Siemens documentation before purchase or installation.

Technical Data & PDF

Manufacturer Siemens
Full part number C79458-L2343-A2
Component scope Siemens Industrial Communication Communication Component; verify complete assembly and accessories separately
Product family Siemens Industrial Communication
Platform Siemens Siemens Industrial Communication
Configuration Complete assembly code and revision to be matched
Installation Match label photos, host assembly, connector layout and supported driver/project.
Official document Siemens product support and current manufacturer documentation
Siemens official product documentationVerify ordering data, compatibility, installation, diagnostics and migration guidance for the exact article number
Open Siemens Support

System Match & FAQ

C79458-L2343-A2Siemens Industrial Communication Communication Component
→
Host PlatformSiemens Industrial Communication / Siemens automation
→
Configuration CheckMatch wiring, firmware, accessories and project release

Use C79458-L2343-A2 only in a correctly matched Siemens configuration. Final performance and interchangeability depend on the complete installed system and approved engineering data.

Product FAQ

What identification is needed before ordering C79458-L2343-A2?

For C79458-L2343-A2, provide the full assembly label and revision plus the host-system identification. An assembly code or similar board appearance alone does not verify driver support or interchangeability.

Where is C79458-L2343-A2 typically applied?

C79458-L2343-A2 is intended for maintenance of the identified siemens communication installation. Match the complete installed system and approved engineering data.

What should be checked before installing C79458-L2343-A2?

C79458-L2343-A2: Match label photos, host assembly, connector layout and supported driver/project.

How should C79458-L2343-A2 be commissioned?

C79458-L2343-A2: Preserve the original configuration and validate communication with the approved host system.

What is needed to order C79458-L2343-A2?

Quote the complete C79458-L2343-A2 order number, installed revision, quantity and destination. Include label photos, the Siemens Industrial Communication configuration and required accessories.

Request a Verified Quotation

Send the complete C79458-L2343-A2 model, quantity, installed Siemens platform, destination and clear label photos. Availability and condition will be confirmed before quotation.

Official manufacturer source: Siemens product support and current official documentation. Final suitability must be verified against the exact installed system, revision and model suffix.
✉Need this part?Quick Inquiry

We found other products you might like!

APOGEE Power Open Processor | 562-001 | Siemens
APOGEE Power Open Processor | 562-001 | Siemens
In Stock Original New Unused Siemens 562-001 APOGEE Power Open Processor
500-033260 Siemens DPU Device Programmer Test Unit
500-033260 Siemens DPU Device Programmer Test Unit
Siemens · Siemens Fire Safety Device Programming Units 500-033260 500-033260 is Siemens model DPU, a compact portable device programmer and test unit for FireFinder XLS and MSL devices. Siemens states that 500-033260 electronically programs and tests compatible detectors before installation through device microcomputer-chip non-volatile memory; it is an accessory, not a detector or control panel. Type DPU device programmer and test unit for FireFinder XLS and MSL devices Family Siemens Fire Safety Device Programming Units Platform Siemens FireFinder XLS and MSL device ecosystem Scope Component ✉ sales1@amikon.cnWhatsApp +86 18150117685 Application & Order CheckVerify 500-033260 against the installed Siemens configuration Application Fit Maintenance of the documented Siemens Fire Safety Device Programming Units installation Like-for-like replacement using the complete Siemens identifier Migration planning with Siemens lifecycle and compatibility guidance Verify Before Order Complete order number 500-033260 Hardware revision, firmware and project compatibility verify the target detector/device family, current instructions, battery/charger condition, firmware compatibility and the fire-system commissioning procedure. Scope note: 500-033260 is a portable programming/test accessory, not a detector or fire alarm control panel. Only manufacturer-documented component data is stated on this page.
505-7003 Siemens SIMATIC TI505 Counter Encoder Module
505-7003 Siemens SIMATIC TI505 Counter Encoder Module
Siemens · SIMATIC TI505 505-7003 505-7003 is a Siemens SIMATIC TI505 high-speed counter encoder I/O module. Siemens specifies two channels with six counters total-one 24-bit counter and two 16-bit counters per channel-plus eight discrete outputs, quadrature and non-quadrature modes, and a 100 kHz default input filter. Type SIMATIC TI505 high-speed counter encoder module Family SIMATIC TI505 Platform Siemens SIMATIC TI505 PLC system Scope Component ✉ sales1@amikon.cnWhatsApp +86 18150117685 Application & Order CheckVerify 505-7003 against the installed Siemens configuration Application Fit Maintenance of the documented SIMATIC TI505 installation Like-for-like replacement using the complete Siemens identifier Migration planning with Siemens lifecycle and compatibility guidance Verify Before Order Complete order number 505-7003 Hardware revision, firmware and project compatibility verify the TI505 base, supported CPU release, terminal block, field input level, external 24 VDC output supply, jumper configuration and ladder-logic configuration. Scope note: 505-7003 is a single-wide TI505 I/O module, not a PLC CPU or complete system. Only manufacturer-documented component data is stated on this page.
6AR1304-0CA00-0AA0 Siemens SICOMP SMP16-SFT304 Module
6AR1304-0CA00-0AA0 Siemens SICOMP SMP16-SFT304 Module
Siemens · SICOMP SMP16 6AR1304-0CA00-0AA0 6AR1304-0CA00-0AA0 is Siemens product designation SMP16-SFT304 for the SICOMP SMP16 industrial microcomputer platform. Siemens technical documentation identifies SMP16-SFT304 as a separate interrupt controller board on the SMP16 bus; it is a legacy, deleted product and must be matched by complete MLFB and system configuration. Type SICOMP SMP16-SFT304 interrupt controller board Family SICOMP SMP16 Platform Siemens SICOMP SMP16 industrial microcomputer Scope Component ✉ sales1@amikon.cnWhatsApp +86 18150117685 Application & Order CheckVerify 6AR1304-0CA00-0AA0 against the installed Siemens configuration Application Fit Maintenance of the documented SICOMP SMP16 installation Like-for-like replacement using the complete Siemens identifier Migration planning with Siemens lifecycle and compatibility guidance Verify Before Order Complete order number 6AR1304-0CA00-0AA0 Hardware revision, firmware and project compatibility verify the SMP16 CPU generation, bus slot, interrupt routing, software support and the complete MLFB before installation. Scope note: 6AR1304-0CA00-0AA0 is an SMP16 bus interrupt controller board, not a standalone controller system. Only manufacturer-documented component data is stated on this page.
6AV3503-1DB10 Siemens SIMATIC OP3 Operator Panel
6AV3503-1DB10 Siemens SIMATIC OP3 Operator Panel
Siemens · SIMATIC HMI OP3 6AV3503-1DB10 6AV3503-1DB10 is a Siemens SIMATIC OP3 operator panel with a two-line, 20-character STN display, membrane keypad, MPI interface and RS232 configuration interface. Siemens specifies 24 VDC nominal supply, a 148 x 76 x 27 mm front panel and IP65 protection at the front when the gasket is correctly installed. Type SIMATIC OP3 operator panel Family SIMATIC HMI OP3 Platform Siemens SIMATIC HMI Scope Component ✉ sales1@amikon.cnWhatsApp +86 18150117685 Application & Order CheckVerify 6AV3503-1DB10 against the installed Siemens configuration Application Fit Maintenance of the documented SIMATIC HMI OP3 installation Like-for-like replacement using the complete Siemens identifier Migration planning with Siemens lifecycle and compatibility guidance Verify Before Order Complete order number 6AV3503-1DB10 Hardware revision, firmware and project compatibility verify the panel cutout, 24 VDC supply, MPI/PPI network parameters, controller type, cable and legacy ProTool project compatibility. Scope note: 6AV3503-1DB10 is an operator panel, not a PLC or complete automation system. Only manufacturer-documented component data is stated on this page.
Siemens 6FX2001-5FN13 Motion Control Encoder PROFINET Single-Turn Absolute Encoder
6FX2001-5FN13 Siemens Motion Control Encoder PROFINET Single-Turn Absolute Encoder
Siemens · Motion Control Encoder 6FX2001-5FN13 6FX2001-5FN13 is a Siemens PROFINET Single-Turn Absolute Encoder in the Motion Control Encoder family. Single-turn absolute encoder; PROFINET; current FS15 catalog version 16-bit; 10–30 V DC; 6 mm shaft. Intended for PROFINET rotary-position measurement and motion control. Type PROFINET Single-Turn Absolute Encoder Family Motion Control Encoder Platform Siemens Motion Control Encoder Scope Component ✉ sales1@amikon.cnWhatsApp +86 18150117685 Application & Order CheckMatch 6FX2001-5FN13 to the installed Siemens configuration Application Fit PROFINET rotary-position measurement and motion control Single-turn absolute encoder; PROFINET; current FS15 catalog version 16-bit; 10–30 V DC; 6 mm shaft Like-for-like replacement with verified Motion Control Encoder configuration Verify Before Order Match the synchronous flange, 6 mm shaft, radial M12 connections, operating supply and encoder function status. Complete 6FX2001-5FN13 article number and hardware revision Use the GSDML matching the function status, select the approved telegram, then verify preset, counting direction and measured angle. Scope note: 6FX2001-5FN13 is supplied as PROFINET Single-Turn Absolute Encoder; system engineering, accessories and site acceptance are verified separately.
Siemens 6GK5206-2BD00-2AC2 SCALANCE X206 Managed Switch
6GK5206-2BD00-2AC2 Siemens SCALANCE X206 Managed Switch
SIEMENS · SIMATIC NET / SCALANCE 6GK5206-2BD00-2AC2 6GK5206-2BD00-2AC2 is a Siemens SCALANCE X206 Managed Switch. Match the complete MLFB, hardware revision, installed system and project release before replacement or commissioning. Type Industrial communication module Family SIMATIC NET / SCALANCE Platform SIMATIC NET / SCALANCE Scope Exact MLFB and installed configuration ✉ sales1@amikon.cnWhatsApp +86 18150117685 Application & Order CheckVerify 6GK5206-2BD00-2AC2 against the installed Siemens configuration Application Fit Like-for-like Siemens spare replacement Documented automation, HMI or network service Migration planning with approved project backup Verify Before Order Complete MLFB, suffix and hardware revision Rack, panel, connector, power and network compatibility Firmware, project release and accessory configuration Scope note: 6GK5206-2BD00-2AC2 is supplied as Industrial communication module; system engineering, accessories and site acceptance are verified separately.
Siemens 6AU1455-2AD00-0AA0 SIMOTION Controller Module
6AU1455-2AD00-0AA0 Siemens SIMOTION Controller Module
SIEMENS · SIMOTION 6AU1455-2AD00-0AA0 6AU1455-2AD00-0AA0 is the Siemens SIMOTION Controller Module identified by the complete order number 6AU1455-2AD00-0AA0. The full MLFB, hardware revision, installed system and project release must be matched before replacement or commissioning. Type Motion-control module Family SIMOTION Platform SIMOTION Scope Exact MLFB and installed configuration ✉ sales1@amikon.cnWhatsApp +86 18150117685 Application & Order CheckVerify 6AU1455-2AD00-0AA0 against the installed Siemens configuration Application Fit Like-for-like Siemens spare replacement Documented automation, HMI, network or drive service Migration planning with approved project backup Verify Before Order Complete MLFB, suffix and hardware revision Rack, panel, connector, power and network compatibility Firmware, project release and accessory configuration Scope note: 6AU1455-2AD00-0AA0 is supplied as Motion-control module; system engineering, accessories and site acceptance are verified separately.

What Our Clients Say?

Available every working day from 8:00AM to 8:00PM Contact us to place an enquiry

Email us : sales1@amikon.cn

Reply within one working day

Visit us

32D Guomao Building, No.388, Hubin South Road, Siming District

Please read on, stay posted, subscribe, and we welcome you to tell us what you think.

submit
Contact Us
Location 32D Guomao Building, No.388, Hubin South Road, Siming District

Disclaimer : Salesplcauto sells new and surplus products and develops channels for purchasing such products. This website has not been approved or recognized by any of the listed manufacturers or trademarks. Salesplcauto is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.



Copyright @2026 SalesPlc Limited. Sitemap / Blog / XML / Terms And Conditions / Privacy Policy Network Supported

vk YouTube Tiktok Pinterest Reddit teitter linkedin. facebook

leave a message

leave a message
Feel free to communicate any order concerns – we provide quality products and best service.
submit

Home

Products

whatsApp

Contact Us

About Us

Reliable Industrial Automation Parts, Global Supply Support SALES PLC works with a broad network of qualified suppliers to provide industrial automation components that meet our customers’ requirements for quality, availability, price, and delivery time. Our product portfolio covers PLC, DCS, HMI, control systems, safety systems, drives, communication modules, and other critical spare parts from leading brands, including Siemens, Emerson, Invensys Triconex, HIMA, GE, ABB, Honeywell, and Bently Nevada. More Than Products — Complete Supply Solutions Our strength goes beyond product sourcing. We work closely with end users, system integrators, maintenance teams, and industrial partners to identify suitable replacement parts and practical procurement solutions. Through integrated purchasing and online support, customers can send inquiries and place orders throughout the year. Our experienced team responds quickly and helps reduce downtime caused by unavailable or obsolete equipment. Our Team Our experienced team brings together product specialists, sourcing professionals, sales consultants, and customer service staff. We work together to provide clear communication and dependable support at every stage of the order. Growing Together for More Than 20 Years For more than 20 years, SALES PLC has continued to grow with the support and trust of customers, suppliers, and business partners around the world. Every project, inquiry, and partnership has helped us improve our service. Looking ahead, we remain committed to providing dependable products, responsive communication, and professional industrial automation solutions. Thank you to every customer and partner who has supported our journey. We look forward to building a stronger and more successful future together. Sustainable Partnerships SALES PLC believes in building long-term, mutually beneficial relationships with customers and suppliers. We focus on honest communication, responsible sourcing, continuous improvement, and reliable service. As industrial technology continues to evolve, we keep expanding our product knowledge and supplier network to support new systems, legacy equipment, and replacement-part requirements. Contact SALES PLC Our team is available during working hours to answer your questions, check product availability, and prepare a quotation.

Where to Find Us

32D Guomao Building, No.388, Hubin South Road, Siming District +86 18150117685 sales1@amikon.cn

Follow Us