AO610
Analog Output · 16 Channels · 3BHT300008R1
Lifecycle note: ABB AO610 is an S600 I/O analog output module with channels opto-isolated as one group. Preserve the installed output mapping and verify the complete article number before replacement.
Product Condition
Original New with One Year WarrantyParts Available
In Stock and Same Day ShippingDelivery Mode
Shipping via DHL Fedex or UPS etcEmail:
sales17@amikon.cnWhatsapp/Mob:
+86 153 5940 8275Analog Output Module · S600 I/O
ABB AO610, article number 3BHT300008R1, is a 16-channel analog output module in the S600 I/O family. The manufacturer specifies 12-bit resolution and 0–20 mA or 0–10 V output ranges. Its electrical output type must be matched to the receiving actuator, positioner or other analog-input device rather than selected solely from the module appearance.
The output channels are opto-isolated as one group. This is a group-isolation arrangement, not a statement of individual channel-to-channel isolation. Engineering review should retain the selected current or voltage interface, channel assignments, signal returns and the receiving equipment’s input specification. ABB lists net dimensions of 40 mm width, 273 mm height and 252 mm depth, with a net weight of 1.25 kg; cabinet and handling checks should use these dimensions alongside the installed mounting and connector arrangement.
For a planned replacement, preserve the existing output mapping and record the process response expected at each test point before the change. Conduct loop checks under the site’s approved isolation and commissioning procedure, with actuators secured against unintended movement. MRO purchasing and supplier acceptance should identify both AO610 and 3BHT300008R1, retain the offered unit’s revision and serial-number evidence, and distinguish a documented operational test from a visual inspection or a generic statement that a board powers up.
| Manufacturer | ABB |
|---|---|
| Model | AO610 |
| Article number | 3BHT300008R1 |
| Module type | Analog Output Module |
| I/O family | S600 I/O |
| Output channels | 16 |
| Resolution | 12 bits |
| Current output range | 0–20 mA |
| Voltage output range | 0–10 V |
| Isolation arrangement | Opto-isolated as one group |
| Net width | 40 mm |
| Net height | 273 mm |
| Net depth / length | 252 mm |
| Net weight | 1.25 kg |
Preserve the S600 output configuration and actuator loop records before replacement or migration.
ABB describes the outputs as opto-isolated as one group. Do not interpret this as a separate isolation barrier for every channel. Check the shared signal-return arrangement and connected equipment before combining loops with different reference potentials.
No. AO610 supports both published signal ranges, but voltage and current interfaces require the correct configured output and wiring. Match the receiving device’s input mode and documented terminals; do not interchange connections merely because the commanded engineering value is identical.
The product detail sheet states 0–20 mA. Establish the required 4 mA live-zero mapping in the applicable system documentation and project configuration, then verify measured low, intermediate and high outputs. Do not advertise a separate native 4–20 mA hardware mode from the product sheet alone.
It specifies output conversion resolution. It does not by itself establish overall accuracy, temperature drift, output settling time or the minimum useful actuator movement. Obtain those limits from the applicable system manual and receiving-device specification when defining an acceptance test.
The full article number ties the delivered module to the purchase requirement. Record a readable article label, revision and connector condition, and reconcile them with the supplier’s unit-specific evidence before releasing the spare to stores.
Use ABB’s net width of 40 mm, height of 273 mm and depth of 252 mm. These are product dimensions, not a complete installation clearance envelope; allow the space required by the actual mounting, connectors and cable routing.
A useful report identifies the tested channels, selected signal mode, applied load and measured values at the agreed command points. Include test-equipment traceability and the offered unit’s serial identity. Apply acceptance tolerances from the relevant documented limits rather than inventing an accuracy figure from the 12-bit resolution.
Place affected loops in the approved maintenance state, secure the process and record the intended output commands before the exchange. After installation, verify mapping and measured signals with outputs controlled by the site procedure before restoring normal automatic operation.
Send the model, complete part number, quantity, destination and nameplate photo. We will verify identification details before confirming availability and lead time.
Official PDF: ABB AO610 3BHT300008R1 Product Details. File size is below 1 MB; verify the exact installed hardware and configuration before use.
Visit us
32D Guomao Building, No.388, Hubin South Road, Siming District
Please read on, stay posted, subscribe, and we welcome you to tell us what you think.
Disclaimer : Salesplcauto sells new and surplus products and develops channels for purchasing such products. This website has not been approved or recognized by any of the listed manufacturers or trademarks. Salesplcauto is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.
Copyright @2026 SalesPlc Limited. Sitemap
/ Blog
/ XML
/ Terms And Conditions
/ Privacy Policy
Network Supported
About Us
Reliable Industrial Automation Parts, Global Supply Support SALES PLC works with a broad network of qualified suppliers to provide industrial automation components that meet our customers’ requirements for quality, availability, price, and delivery time. Our product portfolio covers PLC, DCS, HMI, control systems, safety systems, drives, communication modules, and other critical spare parts from leading brands, including Siemens, Emerson, Invensys Triconex, HIMA, GE, ABB, Honeywell, and Bently Nevada. More Than Products — Complete Supply Solutions Our strength goes beyond product sourcing. We work closely with end users, system integrators, maintenance teams, and industrial partners to identify suitable replacement parts and practical procurement solutions. Through integrated purchasing and online support, customers can send inquiries and place orders throughout the year. Our experienced team responds quickly and helps reduce downtime caused by unavailable or obsolete equipment. Our Team Our experienced team brings together product specialists, sourcing professionals, sales consultants, and customer service staff. We work together to provide clear communication and dependable support at every stage of the order. Growing Together for More Than 20 Years For more than 20 years, SALES PLC has continued to grow with the support and trust of customers, suppliers, and business partners around the world. Every project, inquiry, and partnership has helped us improve our service. Looking ahead, we remain committed to providing dependable products, responsive communication, and professional industrial automation solutions. Thank you to every customer and partner who has supported our journey. We look forward to building a stronger and more successful future together. Sustainable Partnerships SALES PLC believes in building long-term, mutually beneficial relationships with customers and suppliers. We focus on honest communication, responsible sourcing, continuous improvement, and reliable service. As industrial technology continues to evolve, we keep expanding our product knowledge and supplier network to support new systems, legacy equipment, and replacement-part requirements. Contact SALES PLC Our team is available during working hours to answer your questions, check product availability, and prepare a quotation.
Where to Find Us
32D Guomao Building, No.388, Hubin South Road, Siming District
+86 18150117685
sales1@amikon.cn
Follow Us
