Vibro-Meter CPUM 200-595-072-422 CPUM Modular CPU and Rack Controller Card
CPUM 200-595-072-422
CPUM Modular CPU and Rack Controller Card · VM600 Rack Controller and Communications Card for Vibro-Meter VM600 Machinery Protection System
Lifecycle note: Use the unit nameplate and current Vibro-Meter documentation as final references before approving a replacement.
Product Condition
Original New with One Year WarrantyParts Available
In Stock and Same Day ShippingDelivery Mode
Shipping via DHL Fedex or UPS etcEmail:
sales17@amikon.cnWhatsapp/Mob:
+86 15359408275CPUM Modular CPU and Rack Controller Card · Vibro-Meter VM600 Machinery Protection System
Vibro-Meter CPUM 200-595-072-422 is a modular CPUM card that functions as the rack controller and communications gateway for a VM600 machinery protection or condition monitoring rack. The complete PNR identifies both firmware 072 and the installed hardware arrangement.
The CPUM centralizes rack configuration, event logging, front-panel status display and communication with protection cards through the VME backplane. With its IOCN partner, Vibro-Meter CPUM 200-595-072-422 exposes serial and Ethernet interfaces for MPSx, Modbus and the functions supported by its firmware.
Vibro-Meter CPUM 200-595-072-422 uses serial-redundant cpum with additional serial communications module hardware. The CPU platform is documented with an AMD Geode LX800 processor at 500 MHz, 256 MB DRAM and a 5 VDC input below 1.8 A; communication capability still depends on firmware and jumper configuration.
Before replacing Vibro-Meter CPUM 200-595-072-422, export the rack configuration, record IP and fieldbus settings, confirm the IOCN version and check the complete hardware revision. Similar CPUM suffixes are not interchangeable solely because the front-panel appearance is the same.
| Manufacturer | Vibro-Meter |
|---|---|
| Complete model | CPUM 200-595-072-422 |
| Product type | VM600 Rack Controller and Communications Card |
| System family | Vibro-Meter VM600 Machinery Protection System |
| Firmware identifier | 072 |
| Hardware identifier | 422 |
| Hardware arrangement | Serial-redundant CPUM with additional serial communications module |
| Product role | VM600 rack controller and communications gateway |
| Companion interface card | IOCN |
| CPU module | PFM-541I or equivalent |
| Processor | AMD Geode LX800, 500 MHz |
| CPU memory | 256 MB DRAM |
| CPU-module input | 5 VDC, <1.8 A |
| Primary serial interface | RS-232, up to 115.2 kBaud |
| Secondary serial interface | RS-232 or RS-485, up to 115.2 kBaud, 500 VDC isolation |
| Primary Ethernet | 10/100BASE-TX, up to 100 Mbps, up to 100 m |
| Secondary Ethernet | 10/100BASE-TX, up to 10 Mbps, up to 100 m |
| Internal rack interface | VME A24 / D16 master mode |
| Time synchronization | NTP server or battery-backed real-time clock |
| Rack supply | 5 VDC |
| CPUM power consumption | <10 W |
| CPUM / IOCN pair consumption | ≤12 W |
| Operating temperature | −20 to 65°C (−4 to 149°F) |
| Storage temperature | −25 to 80°C (−13 to 176°F) |
| Humidity | 0–90% RH, non-condensing |
| CPUM dimensions | 6U × 40 × 187 mm (262 × 40 × 187 mm) |
| Approximate CPUM weight | 0.40 kg (0.88 lb) |
| Additional serial interfaces | 2 × RS-422 / RS-485, up to 115.2 kBaud |
| Additional serial-module input | 5 VDC, <220 mA |
| Additional serial isolation | >100 VDC |
Use the installed-unit nameplate, current Vibro-Meter documentation and approved site records as final references.
Vibro-Meter CPUM 200-595-072-422 is a modular VM600 CPUM rack controller and communications gateway identified with firmware 072 and serial-redundant cpum with additional serial communications module hardware.
The documented CPUM platform for Vibro-Meter CPUM 200-595-072-422 uses an AMD Geode LX800 processor at 500 MHz with 256 MB DRAM.
Vibro-Meter CPUM 200-595-072-422 belongs to the CPUM/IOCN platform with RS-232 or RS-485 serial communication and 10/100BASE-TX Ethernet. Exact protocols depend on firmware, hardware and configuration.
The 072 portion of Vibro-Meter CPUM 200-595-072-422 identifies the CPUM firmware family. Preserve the installed CompactFlash and confirm the running version in the system version record.
The 422 hardware portion of Vibro-Meter CPUM 200-595-072-422 identifies serial-redundant cpum with additional serial communications module and its major/minor hardware revisions; major changes can affect interchangeability.
Vibro-Meter CPUM 200-595-072-422 can use the corresponding IOCN rear interface for secondary Ethernet and serial connectors. Verify the exact IOCN PNR, jumpers and rack wiring.
Restore only the approved CPUM and MPSx configuration for Vibro-Meter CPUM 200-595-072-422, then verify IP addressing, time synchronization, rack inventory, fieldbus communication and event logging.
Another CPUM suffix must not replace Vibro-Meter CPUM 200-595-072-422 until firmware, hardware arrangement, CompactFlash, IOCN compatibility, interfaces and rack configuration are confirmed.
Provide the complete Vibro-Meter CPUM 200-595-072-422 PNR, revision, serial number, IOCN PNR, rack model, firmware backup, interface requirements, quantity and destination.
Send the complete Vibro-Meter model, revision, quantity, destination and nameplate photo. We will verify identification details before confirming availability and lead time.
Visit us
32D Guomao Building, No.388, Hubin South Road, Siming District
Please read on, stay posted, subscribe, and we welcome you to tell us what you think.
Disclaimer : Salesplcauto sells new and surplus products and develops channels for purchasing such products. This website has not been approved or recognized by any of the listed manufacturers or trademarks. Salesplcauto is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.
Copyright @2026 SalesPlc Limited. Sitemap
/ Blog
/ XML
/ Terms And Conditions
/ Privacy Policy
Network Supported
About Us
Reliable Industrial Automation Parts, Global Supply Support SALES PLC works with a broad network of qualified suppliers to provide industrial automation components that meet our customers’ requirements for quality, availability, price, and delivery time. Our product portfolio covers PLC, DCS, HMI, control systems, safety systems, drives, communication modules, and other critical spare parts from leading brands, including Siemens, Emerson, Invensys Triconex, HIMA, GE, ABB, Honeywell, and Bently Nevada. More Than Products — Complete Supply Solutions Our strength goes beyond product sourcing. We work closely with end users, system integrators, maintenance teams, and industrial partners to identify suitable replacement parts and practical procurement solutions. Through integrated purchasing and online support, customers can send inquiries and place orders throughout the year. Our experienced team responds quickly and helps reduce downtime caused by unavailable or obsolete equipment. Our Team Our experienced team brings together product specialists, sourcing professionals, sales consultants, and customer service staff. We work together to provide clear communication and dependable support at every stage of the order. Growing Together for More Than 20 Years For more than 20 years, SALES PLC has continued to grow with the support and trust of customers, suppliers, and business partners around the world. Every project, inquiry, and partnership has helped us improve our service. Looking ahead, we remain committed to providing dependable products, responsive communication, and professional industrial automation solutions. Thank you to every customer and partner who has supported our journey. We look forward to building a stronger and more successful future together. Sustainable Partnerships SALES PLC believes in building long-term, mutually beneficial relationships with customers and suppliers. We focus on honest communication, responsible sourcing, continuous improvement, and reliable service. As industrial technology continues to evolve, we keep expanding our product knowledge and supplier network to support new systems, legacy equipment, and replacement-part requirements. Contact SALES PLC Our team is available during working hours to answer your questions, check product availability, and prepare a quotation.
Where to Find Us
32D Guomao Building, No.388, Hubin South Road, Siming District
+86 18150117685
sales1@amikon.cn
Follow Us
